Easy’s Slipper™ heartbar "Rocker" (fronts)745-0001-622
for fitting instructions scroll down
Easy’s Slipper® provides physical benefits to your horse, including
- Natural flexion of the hoof
- Reduces pain and lameness
- Increases oxygenation of the horses’ body
- Enhances movement with adjustable rocker
- Reduces stress on bones, ligaments and joints
- Eliminates hoof damage associated with traditional shoeing
- Improves mental state Better overall hoof health
Easy’s Slipper® from Advanced Equine Comfort LLC is a flexible horse shoe alternative, providing therapeutic benefits by utilizing scientific data and innovative materials to protect and grow healthier hooves and happier horses. Easy’s Slipper®, a lightweight glue-on made from flexible durable material, lasts the full six to eight week shoeing cycle. The slipper allows for the natural flexion of the hoof, while reducing pain and lameness. Additional therapeutic benefits include healthy hoof growth, as well as reduced pain, inflammation and stress to the ligaments, bones, joints and tendons. Regardless of the discipline, any horse can benefit from Easy’s Slipper® innovative horseshoe alternative.
WHAT YOU NEED TO HAVE BEFORE YOU GET STARTED:
Products available from Easy’s Slipper®
- Easy’s Slipper® Therapeutic and Performance Slipper™ or Pads
- Hoof Tite Glue, mixing tips, and glue gun
- Hoof Life Silicone Packing
- Moisture meter (available in starter kit or locally)
- Mini-Butane Torch (available in Starter Kit or locally)
Products to buy Locally
- Latex gloves (change often)
- Wire brush
- Sandpaper – 60 grit or rougher
- Denatured alcohol
- Play Dough
- Paper towels or a rag
- Hoof Knife
When applying Easy’s Slipper®, it is important to take into account the environmental factors (e.g. humidity, temperature, etc) for proper glue application and bonding. Please follow the glue manufacturer suggested conditions for optimal application temperatures and conditions.
Easy’s Slipper® should ONLY be applied after cleaning and trimming the hooves.
- Make sure the hoof wall is clean. Rough up the hoof wall by rasping and sanding . Use 60 grit or rougher sand paper. You may prefer to use your electric buffy.
- It is CRITICAL to check the moisture in the hoof where the cuff will cover with a moisture meter. If the moisture reading is greater than zero, go around the hoof wall with a mini torch and recheck the moisture reading. Typically, the hoof will reach a moisture reading of zero after two or three passes with the torch. Between passes, use a wire brush to scuff up the hoof wall.
- At this point, put on latex gloves as the procedure above removed any oils that might have been on the hoof wall. Clean the inside of the slipper with denatured alcohol. (Use acetone if using Equilox glue). Do not use the mini torch on the inside cuff of the slipper.
- Dry fit the slipper. Visually it is easy to check the appropriate length. To check the width, move the slipper from left to right. There should be little if any movement. Let your horse walk up and down the shed row prior to preparing for gluing. Lift the hoof
- Prepare the glue. Most glue has an optimal temperature for use around 72 degrees. Either warm the glue with hot water or cool it with cold water.
- PURGE THE GLUE prior to putting on a mixing tip. When material comes out of both sides equally (sometimes 3-4 pumps of the gun), you can place the mixing tip on the tube. THIS STEP IS CRITICAL FOR A PROPER BOND.
- Have an assistant pick up the opposite hoof so that the horse is bearing its weight on the hoof you are gluing. Keep a hoof knife in your hand, while gluing, to pull the slipper away from the hoof wall in case of inadequate glue coverage. Go around the slipper and insert the glue in the pre-drilled holes and begin the gluing process. The dispersion of glue can be seen through the slipper. It is essential to get as close to 100% glue coverage on the cuff as possible. Move quickly as most glues setup within 30 seconds. Change tips often. Use at least two tips per slipper. (After you have mastered gluing you’ll us less!) Have extra tips available in case the glue starts to setup within the mixing nozzle. You will know because it will become harder to dispense the glue. If any part of the glue starts to come out the back of either side of the tube, stop and replace the glue with another tube as the mixing ratio will be changed and the glue bond will be compromised. After the glue has setup, you can place the hoof that was being held back on the ground. Usually within a minute.
- Replace the mixing nozzle and repeat the process on the other hoof.
- Use a hoof knife and rasp to dress the slipper by removing any excess material.
- We recommend filling in under the back bar to prevent debris from collecting under the heal bulbs. HOOF LIFE may be used under the bar for open bottom and heart bar slippers. Regardless of which style of slipper you are using we recommend putting Artimud in the frog grooves to prevent any thrush.
Happy trails from Easy’s Slipper® Better Shoe – Better Horse
If you have any questions, please contact us at firstname.lastname@example.org
sold in pairs